• Safety switch with integrated evaluation electronics
• Possible to switch pulsed signals
• 2 safety outputs (semiconductor outputs)
• Category 4/PL e according to EN ISO 13849-1
• Multicode

Approach directionCan be adjusted in 90° steps Multicode evaluationEvery suitable actuator is detected by the evaluation unit. Category according to EN ISO 13849-1Due to two redundantly designed semiconductor outputs (safety outputs) with internal monitoring suitable for:

• Category 4/PL e according to EN ISO 13849-1

LED indicator

STATE	Status LED
OUT/ERROR	Safety outputs status / diagnostics LED (combined)

Additional connection

OUT	Monitoring output (semiconductor)

Attention:The operating distance may vary depending on the background material and installation situation. (Only in combination with actuator CES-A-BBA, CES-A-BCA) Typical operating distance For a side approach direction for the actuator and safety switch, a minimum distance of s = 4 mm must be maintained so that the operating distance of the side lobes is not entered. (Only in combination with actuator CES-A-BPA) Typical operating distance For a side approach direction for the actuator and safety switch, a minimum distance of s = 6 mm must be maintained so that the operating distance of the side lobes is not entered.

Dimensions	According to EN 60947-5-2: (LxWxH) 131x40x40
Housing material	Plastic, PBT
Weight
Net	0,4 kg
Ambient temperature
At UB = 24 V DC	-20 ... 55 °C
Degree of protection	IP67
Mounting distance
Between 2 switches or 2 actuators	min.80 mm
Installation orientation	Any
Tightening torque
Screws fastening bracket read head	max.0,6 Nm
Fixing screws housing	max.1 Nm
Ready delay	max.3 s
Reaction time
After change in the actuation status	max.180 ms
Switching frequency	max.1 Hz
Dwell time	min.0,5 s
Connection	M12 plug connector, 8-pin, screen can be applied

Electrical connection ratings

Operating voltage DC	18 ... 24 ... 27 V DC Regulated, residual ripple < 5 %
Current consumption	80 mA
Fusing
(External) operating voltage	0,25 ... 8 A
Rated insulation voltage Ui	300 V
Rated impulse withstand voltage Uimp	max.1,5 kV
EMC protection requirements	In acc. with EN 60947-5-3
Degree of contamination (external, according to EN 60947-1)	3
	Safety outputs LA / LB
Type of output	Semiconductor outputs, p-switching, short circuit-proof, electrically decoupled
Output voltage
HIGH U(LA)	U(+LA) - 1,5 ... U(+LA) V DC
HIGH U(LB)	U(+LB) - 1,5 ... U(+LB) V DC
LOW U(LA) / U(LB)	0 ... 1 V DC
Output current
per safety output	1 ... 400 mA
Fusing
External, safety circuit U(+LA) / U(+LB)	0.4 A medium slow-blow
Utilization category according to EN 60947-5-2
DC-13	24V 400mA
Switching load
According to UL	max. DC 24 V, class 2
Rated conditional short-circuit current	max.100 A
Discrepancy time
(Between the operating points of both safety outputs)	max.120 ms
Power supply output load
U(+LA) / U(+LB)	24 V DC 18 ... 27 V DC
	Monitoring output OUT
Type of output	Semiconductor output, p-switching, short circuit-proof
Output voltage	0,8 x UB ... UB V DC
Output current	max.20 mA
	STATE LED
LED indicator	Status - LED
	LED OUT / ERROR
LED indicator	Safety outputs status / diagnostics (combined)

Work area

Repeat accuracy R

max.10 %

Other

For the approval according to UL the following applies

Operation only with UL class 2 power supply, or equivalent measures

Reliability values according to EN ISO 13849-1

	Monitoring of the safety guard position
Category	4
Performance Level	PL e
PFHD	3.7 x 10-9
Diagnostic Coverage (DC)	99 %
Mission time	20 y

In combination with Actuator CES-A-BBA, CES-A-BCAOperating distance

Distance s, actuator
Minimum distance for side approach direction	min.3 mm
Switch-on distance
With center offset m=0	20 mm
Assured switch-off distance Sar	max.40 mm
Assured operating distance Sao
With center offset m=0	min.18 mm
Switching hysteresis	min.2 mm

In combination with Actuator CES-A-BPAOperating distance

Distance s, actuator
Minimum distance for side approach direction	min.6 mm
Switch-on distance
With center offset m=0	22 mm
Assured switch-off distance Sar	max.58 mm
Assured operating distance Sao
With center offset m=0	min.15 mm
Switching hysteresis	min.1 mm

In combination with Actuator CES-A-BDA-20Operating distance

Distance s, actuator
Minimum distance for side approach direction	min.4 mm
Switch-on distance
With center offset m=0	21 mm
Assured switch-off distance Sar	max.41 mm
Assured operating distance Sao
With center offset m=0	min.19 mm
Switching hysteresis	min.2 mm

The 097525 industrial spare part is crafted with precision to ensure your machinery operates at peak efficiency. Engineered for industrial products in demanding environments, it guarantees reduced downtime and increased productivity. 097525 components are built to withstand the toughest industrial conditions, making them essential for keeping your operations in the USA running smoothly.

Euchner offers a wide selection of industrial spare parts for different applications. Whether you’re performing maintenance or replacing worn-out parts, 097525 provides long-lasting, reliable solutions. Order your 097525 spare part today for fast delivery across the USA and keep your equipment performing at its best.

For industrial components and spare parts, trust Euchner to supply top-tier products that enhance the lifespan and efficiency of your machinery.

• Delivery of spare parts and industrial equipment throughout the USA by Fedex transport company.
• Flexible payment system accepting bank transfers, MasterCard, VISA, PayPall, App Pay, Google Pay.
• Directly from stock and on order.